1˵
    1TIM1TIM83·κһ·CH4
2ʹû
      KEIL MDK-ARM V5.34.0.0
    Ӳ      N32G031C8L7-STB V1.0
3ʹ˵
    ϵͳ:
        1ʱԴ
                    HSE=8M,PLL=48M,AHB=48M,APB1=48M,APB2=48M,TIM1 CLK=48M,TIM8 CLK=48M
        2˿ã
                    PA8ѡΪTIM1 CH1
                    PA9ѡΪTIM1 CH2
                    PA10ѡΪTIM1 CH3
                    PB13ѡΪTIM1 CH1N
                    PB14ѡΪTIM1 CH2N
                    PB15ѡΪTIM1 CH3N
                    PA11ѡΪTIM1 CH4
                    PA0ѡΪTIM8 CH1
                    PA1ѡΪTIM8 CH2
                    PA2ѡΪTIM8 CH3
                    PB6ѡΪTIM8 CH1N
                    PB7ѡΪTIM8 CH2N
                    PB5ѡΪTIM8 CH3N
                    PA3ѡΪTIM8 CH4
        3TIM
                    TIM1 6·,CH4
                    TIM8 6·,CH4
    ʹ÷
        1򿪵ģʽʾ߼ǹ۲TIM1 TIM8
        2TIM1 3·һ·CH4TIM8 3·һ·CH4
4ע
       ĬPA9PA10ñӵNSLINK⴮ڣPA9PA10ڣ;εñ

1. Function description
    1. TIM1 and TIM8 output 3 complementary waveforms and 1 CH4 waveform
2. Use environment
    Software development environment: KEIL MDK-ARM V5.34.0.0
    Hardware environment: Developed based on the evaluation board N32G031C8L7-STB V1.0
3. Instructions for Use
    System configuration;
        1. Clock source:
            HSE=8M, PLL=48M, AHB=48M, APB1=48M, APB2=48M, TIM1 CLK=48M, TIM8 CLK=48M
        2. Port configuration:
                    PA8 is selected as TIM1 CH1 output
                    PA9 is selected as TIM1 CH2 output
                    PA10 is selected as TIM1 CH3 output
                    PB13 is selected as TIM1 CH1N output
                    PB14 is selected as TIM1 CH2N output
                    PB15 is selected as TIM1 CH3N output
                    PA11 is selected as TIM1 CH4 output
                    PA0 is selected as TIM8 CH1 output
                    PA1 is selected as TIM8 CH2 output
                    PA2 is selected as TIM8 CH3 output
                    PB6 is selected as TIM8 CH1N output
                    PB7 is selected as TIM8 CH2N output
                    PB5 is selected as TIM8 CH3N output
                    PA3 is selected as TIM8 CH4 output
        3. TIM:
            TIM1 6 complementary outputs, CH4 output
            TIM8 6 complementary outputs, CH4 output
    Instructions:
        1. Open debugging mode after compilation and use an oscilloscope or logic analyzer to observe the output waveform of TIM1 TIM8
        2. Output waveform TIM1 3-way complementary plus one CH4, TIM8 3-way complementary plus one CH4
4. Matters needing attention
       By default, the PA9 and PA10 jumper caps of the development board are connected to the virtual serial port of NSLINK. If PA9 and PA10 are not used as serial ports in the project, and are used for other purposes, the serial port jumper caps must be unplugged.
