1˵

    òʾLPUARTUSARTzͨDMAѯʵֵĻͨšUSARTz
USART1
    ȣDMATxBuffer1LPUARTݼĴݷ
USARTzUSARTzݣDMAUSARTzݼĴRxBuffer2
ȽաݣȽϽTransferStatus2
    ͬʱDMATxBuffer2USARTzݼĴݷ
LPUARTLPUARTݣDMALPUARTݼĴRxBuffer1
ȽաݣȽϽTransferStatus1   


2ʹû

    KEIL MDK-ARM Professional Version 5.26.2.0

    ӲСϵͳСϵͳN32G031C8L7-STB V1.0


3ʹ˵
	
    ϵͳʱ£
    - ʱԴ = HSI + PLL
    - ϵͳʱ = 48MHz
    
    LPUART£
    -  = 115200 baud
    - ֳ = 8λ̶
    - 1ֹͣλ̶
    - Уƽ
    - ӲƽãRTSCTSźţ
    - ͷʹ
    - DMAģʽDMAģʽʹ
    
    USART£
    -  = 115200 baud
    - ֳ = 8λ
    - 1ֹͣλ
    - Уƽ
    - ӲƽãRTSCTSźţ
    - ͷʹ
    - DMAģʽDMAģʽʹ
    
    LPUARTUSART£
    - LPUART_Tx.PA1   <------->   USART1_Rx.PA10
    - LPUART_Rx.PA0   <------->   USART1_Tx.PA9

    
    Բ
    - DemoKEIL±MCU
    - λУβ鿴TransferStatus1TransferStatus2У
      PASSEDΪͨFAILEDΪ쳣


4ע

    ȽNS-LINKMCU_TXMCU_RXñϿ

1. Function description

    This test example demonstrates the basic communication between LPUART and USARTz through DMA (query). USARTz can be USART1.
     First, DMA transfers TxBuffer1 data to the LPUART send data register, and then the data is sent to USARTz. USARTz receives data, 
and DMA moves the data from the USARTz receive data register to RxBuffer2.
Compare the received and sent data, and store the comparison result in the TransferStatus2 variable.
     At the same time, DMA transfers TxBuffer2 data to the USARTz send data register, and then the data is sent to LPUART. LPUART 
receives data, DMA moves data from LPUART receive data register to RxBuffer1.
Compare the received and sent data, and the comparison result is stored in the TransferStatus1 variable.


2. Use environment

    Software development environment: KEIL MDK-ARM Professional Version 5.26.2.0

    Hardware environment: minimum system board minimum system board N32G031C8L7-STB V1.0


3. Instructions for use

    The system clock configuration is as follows:
    -Clock source = HSI + PLL
    -System clock = 48MHz
    
    The LPUART configuration is as follows:
    -Baud rate = 115200 baud
    -Word length = 8 data bits (fixed)
    -1 stop bit (fixed)
    -Verification control disabled
    -Hardware flow control disabled (RTS and CTS signals)
    -Receiver and transmitter enable
    -DMA transmit mode and DMA receive mode enable
    
    The USART configuration is as follows:
    -Baud rate = 115200 baud
    -Word length = 8 data bits
    -1 stop bit
    -Verification control disabled
    -Hardware flow control disabled (RTS and CTS signals)
    -Receiver and transmitter enable
    -DMA transmit mode and DMA receive mode enable
    
    The LPUART and USART pin connections are as follows:
    -LPUART_Tx.PA1 <-------> USART1_Rx.PA10
    -LPUART_Rx.PA0 <-------> USART1_Tx.PA9

    
    Test steps and phenomena:
    -After the Demo is compiled in the KEIL environment, download it to the MCU
    -Reset operation, check the variables TransferStatus1 and TransferStatus2 in turn, among them,
      PASSED means the test passed, FAILED means the test is abnormal


4. Matters needing attention

    the MCU_TX and MCU_RX jumper cap of the development board NS-LINK needs to be disconnected first